HOw To HOW TO CUT PLASTIC PANELS

Several people have emailed me offline to ask about the plastic panels we put on the raised beds and how we cut them.  General comments were that they always thought it was difficult and couldn't figure out the easiest way to do it.  I will admit, the first panel I cut, was an epic fail.  It cracked and chipped and broke and just didn't work. I stopped about halfway through and went to the hardware store to figure out the next step.  



I ended up getting a special tool, see below, that worked like a charm.  I laid each 8 foot panel down on the porch and measured from the end to make a mark at the 4 foot point, one at the bottom edge, one in the middle and one at the top edge.  This let me draw a line with a sharpie using a straight edge metal ruler.  Then I just started cutting, following the line.  They cut almost perfectly and gave us a nice stack of 4 foot panels to use on the raised beds.  I did leave the panels out in the sun for a bit, just by chance as I took them out of the car. 


 Even with the right tool, I wouldn't recommend cutting them on a cold day, the sun softened them a bit. Just go slow and steady as you snip, and don't cut all the way to where they are closed.  Just open them wide, cut by squeezing them until about halfway closed, then open wide again and slide along to make the next part of the cut.  If you make the cut to where they close completely, it makes it hard to follow the line and they can still chip a bit.  Of course, we aren't building a house with these so they don't have to be perfect.  It still cut a pretty decent line.  Hope this makes sense.
Tin Snips to cut Plastic Panels
This is what I used.  
They are tin snips.  The exact name on the package says this:

  STRAIGHT CUT TINNER, 12", CUTS UP TO 20 GAUGE STEEL 

 They make them that cut curves, don't get those.  They also make two other smaller sizes that cut a different gauge of steel.  I figured that if these largest ones could cut 20 gauge tin metal, they would cut the plastic panels too.  When we buy a tool we always like to get one that can multitask.  If these will cut the plastic panels now and will someday cut galvanized sheet metal, they'll work great on the farm for years to come!

 Multi tasking tools are almost a necessity!

Comments

Post a Comment

Popular posts from this blog

New Update Methods of Fertilizer Application

Image
Methods of Fertilizer Application. https://cststudy.blogspot.com/ B.Sc.Ag. (Hons) Part-I  Methods of Fertilizer Application Fertilizer recovery is greatly influenced by method of its application. Method of application varies according to the spacing of crop, type of fertilizer material, time of application, etc. A brief account of these points could be explained as under : A.Method of application of solid fertilizer materials Solid materials may be applied in following ways: 1. Broadcasting Even and uniform spreading of dry solid fertilizers by hand or spreader over the entire field before or after sowing of the crop is termed as broadcasting. Well decomposed FYM, compost, oil cake, bone meal, urea, superphosphate and lime are applied by this method. Advantages This method is easy, less time taking, cheap and more convenient to the farmers. This method proves effective- i.                      When the crops have a dense stand ii.                   
Read more

New Update Seed dormancy and its importance

Image
Seed dormancy and its importance. https://cststudy.blogspot.com/                                                Seed Dormancy Definition:   The term dormancy refers to lack of growth in any plant part due to either internally or externally induced factors. Seed technologist use the term of refers to non-germination resulting from conditions within the seeds.  Dormancy is the state of inhibits growth of seeds or other plant organs as a result of internal causes not due to environmental condition. In other word, the unavailability of well developed mature, perfectly viable and healthy seed to germinate when placed under favorable conditions for germination is called dormancy or rest period of seed. Important of seed dormancy: 1. It is a mechanism which helps to survive this species. 2. It prevents the germination of seed in the field during production. 3. Dormancy helps to store the seed in the store house. 4. It contributes the congivity of the species.
Read more

HOw To HORTON HEARS A WHO FLOWERS IN BLOOM

Image
For some reason, these don't always appear at the farm each Spring.  Because of that, we love that somehow they are rarer than the other things popping up on a regular basis.   Dr. Seuss flower? Sure enough, last weekend, they were in a few patches around the farm.  The first time we ever saw one, the FIRST thing we both said was... HORTON HEARS A WHO!!!!!!! The iconic Dr. Seuss character who finds a whole world living on a speck on an awesome looking pink and yellow flower.  Horton Hears a Who flower The only thing missing on ours are the striped stems, ha.  They are SO pretty and so unusual, even if it is "just a weed", we love having them around.   I thought about cutting some to put in a small vase and see how long they last...and maybe we'll just have to start listening a little closer to them. Hmm, just thought about it, maybe I should try to press some in my flower press? 
Read more